Keyless Entry & Smart Systems Bristol

Power over Ethernet (PoE) describes any of several standards or ad hoc systems that pass electric power along with data on twisted-pair Ethernet cabling. This allows a single cable to provide both a data connection and enough electricity to power networked devices such as wireless access points (WAPs), IP cameras and VoIP phones.

There are several common techniques for transmitting power over Ethernet cabling, defined within the broader Institute of Electrical and Electronics Engineers (IEEE) 802.3 standard since 2003.

The three techniques are:

• Alternative A, which uses the same two of the four signal pairs that 10BASE-T and 100BASE-TX use for data in typical Cat 5 cabling.
• Alternative B, which separates the data and the power conductors for 10BASE-T/100BASE-TX, making troubleshooting easier.
• 4PPoE, which uses all four twisted pairs in parallel, increasing the achievable power.

Alternative A transmits power on the same wires as data for common 10 and 100 Mbit/s Ethernet variants. This is similar to the phantom power technique commonly used for powering condenser microphones. Power is transmitted on the data conductors by applying a common voltage to each pair. Because twisted-pair Ethernet uses differential signaling, this does not interfere with data transmission. The common-mode voltage is easily extracted using the center tap of the standard Ethernet pulse transformer. For gigabit Ethernet and faster, both alternatives A and B transmit power on wire pairs also used for data since all four pairs are used for data transmission at these speeds.

4PPoE provides power using all four pairs of the connectors used for twisted-pair Ethernet. This enables higher power for applications like pan–tilt–zoom cameras (PTZ), high-performance wireless access points (WAPs), or even charging laptop batteries.

In addition to standardizing existing practice for common-mode data pair (Alternative A), spare-pair (Alternative B), and four-pair (4PPoE) transmission, the IEEE PoE standards provide for signaling between the power sourcing equipment (PSE) and powered device (PD). This signaling allows the presence of a conformant device to be detected by the power source and allows the device and source to negotiate the amount of power required or available while avoiding damage to non-compatible devices.

The original PoE standard, IEEE 802.3af-2003,^[1] now known as Type 1, provides up to 15.4 W of DC power (minimum 44 V DC and 350 mA)^[2][3] on each port.^[4] Only 12.95 W is guaranteed to be available at the powered device as some power dissipates in the cable.^[5]

The first update to PoE, IEEE 802.3at-2009,^[6] introduced Type 2, also known as PoE+ or PoE plus. It provides up to 25.5 W and prohibits the use of four pairs simultaneously for power.^[7][8]

Both of these standards, 802.3af and 802.3at, were later incorporated into the IEEE 802.3-2012 publication.^[9]

Later Type 3 and Type 4 were introduced in IEEE 802.3bt-2018, respectively supporting up to 51 W and up to 71.3 W delivered power, optionally by using all four pairs for power.^[10] Each pair needs to handle a current of up to 600 mA (Type 3) or 960 mA (Type 4).^[11] Additionally, support for 2.5GBASE-T, 5GBASE-T and 10GBASE-T is included.^[12] This development opens the door to new applications and expands the use of applications such as high-performance wireless access points and surveillance cameras.

IEEE 802.3bt was incorporated into 802.3 in the 2022 revision.^[13]

The IEEE 802.3bu-2016^[14] amendment introduced single-pair Power over Data Lines ( PoDL) for the single-pair Ethernet standards 100BASE-T1 and 1000BASE-T1 intended for automotive and industrial applications.^[15] On the two-pair and four-pair standards, the same power voltage is applied to each conductor of the pair, so that within each pair there is no differential voltage other than that representing the transmitted data. With single-pair Ethernet, power is transmitted in parallel to the data. PoDL initially defined ten power classes, ranging from 0.5 to 50 W (at PD).

Subsequently, PoDL was added to the single-pair variants 10BASE-T1,^[16] 2.5GBASE-T1, 5GBASE-T1, and 10GBASE-T1,^[17] and as of 2021^[update] it includes a total of 15 power classes with additional intermediate voltage and power levels.^[16]

Examples of devices powered by PoE include:^[18]

• VoIP phones
• IP cameras, including PTZs
• WAPs
• IPTV decoders
• Network routers
• A small network switch, providing a small number of Ethernet ports from one uplink cable. Such a switch may in turn pass PoE to downstream devices (termed PoE pass-through).
• Intercom and public address systems
• Wall clocks, with time set using Network Time Protocol (NTP)
• Roof-mounted radios with integrated antennas, 4G/LTE-, 802.11- or 802.16-based systems used by wireless ISPs
• Outdoor point-to-point microwave and millimeter-wave radios and some free space optics units, usually using non-standard, proprietary PoE
• Industrial control system components including sensors, controllers, meters etc.
• Access control components including help points, intercoms, keyless entry, etc.
• Lighting controllers and light-emitting diode (LED) lighting fixtures^[19]
• Stage and theatrical devices, such as networked audio breakout and routing boxes
• Remote point-of-sale (POS) kiosks
• Ethernet repeaters, or extenders, which may also pass PoE through to downstream devices^[20]
• PoE splitters that output the power in a different form (e.g. USB Power Delivery), to power a remote device or charge a mobile phone

802.3 refers to Power Sourcing Equipment (PSE), which provides power on the Ethernet cable. This device may be a network switch, in the standard Endpoint PSE (commonly called an endspan device) or a PoE injector, Midspan PSE in the standard, an intermediary device between a switch that does not provide PoE (or one that cannot provide sufficient power) and a PoE-powered device.^[21]

802.3 refers to any PoE-powered piece of equipment as a Powered Device (PD). Examples include wireless access points, VoIP phones, and IP cameras.

Many powered devices have an auxiliary power connector for an optional external power supply. Depending on the design, some, none, or all of the device's power can be supplied from the auxiliary port,^[22][23] with the auxiliary port also sometimes providing backup power in case PoE-supplied power fails.

Advocates of PoE expect PoE to become a global long-term DC power cabling standard and replace a multiplicity of individual AC adapters, which cannot be easily centrally managed.^[24] Critics of this approach argue that PoE is inherently less efficient than AC power due to the lower voltage, and this is made worse by the thin conductors of Ethernet. Advocates of PoE, like the Ethernet Alliance, point out that quoted losses are for worst-case scenarios in terms of cable quality, length and power consumption by powered devices.^[25] In any case, where the central PoE supply replaces several dedicated AC circuits, transformers and inverters, the power loss in cabling can be justifiable.

The integration of PoE with the IEEE 802.3az Energy-Efficient Ethernet (EEE) standard potentially produces additional energy savings. Pre-standard integrations of EEE and PoE (such as Marvell's EEPoE outlined in a May 2011 white paper) claim to achieve a savings upwards of 3 W per link. This saving is especially significant as higher-power devices come online.^[26]

Standards-based Power over Ethernet is implemented following the specifications in IEEE 802.3af-2003 (which was later incorporated as Clause 33 into IEEE 802.3-2005) or the 2009 update, IEEE 802.3at. The standards require Category 5 cable or better for high power levels but allow using Category 3 cable if less power is required.^[27]

Power is supplied as a common-mode signal over two or more of the differential pairs of wires found in the Ethernet cables and comes from a power supply within a PoE-providing networking device, such as an Ethernet switch, or by a PoE injector, a PoE power source that can be used in combination with a non-PoE switch.

A phantom power technique is used to allow the powered pairs to also carry data. This permits its use not only with 10BASE-T and 100BASE-TX, which use only two of the four pairs in the cable, but also with 1000BASE-T (gigabit Ethernet), 2.5GBASE-T, 5GBASE-T, and 10GBASE-T which use all four pairs for data transmission. This is possible because all versions of Ethernet over twisted pair cable specify differential data transmission over each pair with transformer coupling; the DC supply and load connections can be made to the transformer center-taps at each end. Each pair thus operates in common mode as one side of the DC supply, so two pairs are required to complete the circuit. The polarity of the DC supply may be inverted by crossover cables; the powered device must operate with either pair: the spare pairs on pins 4 and 5, and 7 and 8, or the data pairs on pins 1 and 2, and 3 and 6. Polarity is defined by the standards on spare pairs, and ambiguously implemented for data pairs, with the use of a diode bridge.

Notes:

Three modes, Mode A, Mode B, and 4-pair mode, are available. (In the standard these are discussed as two Modes, with the term 4-pair mode for both simultaneously.) Mode A delivers power on T568A and T568B pairs 2 and 3 – the data pairs of 100BASE-TX or 10BASE-T. Mode B delivers power on pairs 1 and 4 – the pairs not used by 100BASE-TX or 10BASE-T. 4-pair mode delivers power using all four pairs. PoE can also be used with 1000BASE-T, 2.5GBASE-T, 5GBASE-T and 10GBASE-T Ethernet, in which case there are no spare pairs and all power is delivered using the phantom technique.

Mode A has two alternative configurations (MDI and MDI-X), using the same pairs but with different polarities. In Mode A, pins 1 and 2 (pair 3 in T568A wiring, pair 2 in T568B) form one side of the 48 V DC, and pins 3 and 6 (pair 2 in T568A, pair 3 in T568B) form the other side. These are the same two pairs used for data transmission in 10BASE-T and 100BASE-TX, allowing the provision of both power and data over only two pairs in such networks. The free polarity allows PoE to accommodate crossover cables, patch cables and auto MDI-X.

In Mode B, pins 4–5 (pair 1 in both T568A and T568B) form one side of the DC supply and pins 7–8 (pair 4 in both T568A and T568B) provide the return; these are the pairs 10BASE-T and 100BASE-TX do not use. Mode B, therefore, requires that all four pairs of the connectors be wired.

The Power Sourcing Equipment (PSE), not the Powered Device (PD), decides whether Mode A or Mode B shall be used. PDs that implement only Mode A or Mode B are disallowed by the standard.^[37] The PSE can implement Mode A, Mode B, or both (4-pair mode). A PD indicates that it is standards-compliant by placing a 25 kΩ resistor between the powered pairs. If the PSE detects a resistance that is too high or too low (including a short circuit), no power is applied. This protects devices that do not support PoE. An optional power class feature allows the PD to indicate its power requirements by changing the sense resistance at higher voltages.

To retain power, the PD must use at least 5–10 mA for at least 60 ms at a time. If the PD goes more than 400 ms without meeting this requirement, the PSE will consider the device disconnected and, for safety reasons, remove power.^[38]

There are two types of PSE: Endpoint and Midspan. Endpoint devices (commonly PoE switches) are Ethernet networking equipment that includes the power-over-Ethernet transmission circuitry. Midspan devices are power injectors that stand between a non-PoE Ethernet switch (or one that cannot provide sufficient power) and the powered device, injecting power without affecting the data. Endpoint devices are normally used in new installations or where the switch has to be replaced for other reasons (such as moving from 10/100 Mbit/s to 1 Gbit/s), which makes it convenient to add the PoE capability. Midspan PSE can be used e.g. to power a single piece of equipment added to a network that does not provide PoE.

IEEE 802.3at-capable devices are also referred to as Type 2. 802.3at PSE may also use LLDP communication to signal 802.3at capability.^[41]

Class 4 can only be used by IEEE 802.3at (Type 2) devices, requiring valid Class 2 and Mark 2 currents for the power-up stages. An 802.3af device presenting a Class 4 current is non-compliant and, instead, will be treated as a Class 0 device.^{[44]: 13â€Å} 

Link Layer Discovery Protocol (LLDP) is a layer-2 Ethernet protocol for managing devices. LLDP allows an exchange of information between PSE and a PD. This information is formatted in type–length–value (TLV) format. PoE standards define TLV structures used by PSE and PDs to signal and negotiate available power.

The setup phases are as follows:

• The PSE (provider) tests the PD (consumer) physically using 802.3af phase class 3.
  • The PSE provides baseline power to the PD.
• The PD signals to the PSE that it as a PoE PD, indicating its maximum power and requested power.
• The PSE signals to PD that it is PoE PSE, indicating the power allotted to the PD, at which point the PD can begin consuming up to the allotted power.

The rules for this power negotiation are:

• The PD shall never request more power than the physical 802.3af class.
• The PD shall never draw more than the maximum power advertised by the PSE.
• The PSE may deny any PD drawing more power than maximum it has allowed.
• The PSE shall not reduce power allocated to the PD that is in use.
• The PSE may request reduced power, via conservation mode.^{[48]: 10â€Å} 

There are more than ten proprietary implementations.^[49] The more common ones are discussed below.

Some Cisco WLAN access points and VoIP phones supported a proprietary form of PoE^[50] many years before there was an IEEE standard for delivering PoE. Cisco's original PoE implementation is not software upgradeable to the IEEE 802.3af standard. Cisco's original PoE equipment is capable of delivering up to 10 W per port. The amount of power to be delivered is negotiated between the endpoint and the Cisco switch based on a power value that was added to the Cisco proprietary Cisco Discovery Protocol (CDP). CDP is also responsible for dynamically communicating the Voice VLAN value from the Cisco switch to the Cisco VoIP Phone.

Under Cisco's pre-standard scheme, the PSE (switch) will send a fast link pulse (FLP) on the transmit pair. The PD (device) connects the transmit line to the receive line via a low-pass filter. The PSE gets the FLP in return. The PSE will provide a common mode current between pairs 1 and 2, resulting in 48 V DC^[51] and 6.3 W^[52] default of allocated power. The PD must then provide Ethernet link within 5 seconds to the auto-negotiation mode switch port. A later CDP message with a TLV tells the PSE its final power requirement. A discontinuation of link pulses shuts down power.^[53]

In 2014, Cisco created another non-standard PoE implementation called

Universal Power over Ethernet (UPOE). UPOE can use all four pairs, after negotiation, to supply up to 60 W.^[54]

A proprietary high-power development called LTPoE++, using a single Cat 5e Ethernet cable, is capable of supplying varying levels at 38.7, 52.7, 70, and 90 W.^[55]

PowerDsine, acquired by Microsemi in 2007, which was then acquired by Microchip in 2018, has been selling power injectors since 1999. Using Microchip's multi-PoE PSE ICs, PoE injectors and switches can support the IEEE 802.3 PoE standards and also pre-standard configurations. Several companies such as Polycom, 3Com, Lucent and Nortel used PowerDsine's older Power over LAN PoE implementation.^[56]

In a passive PoE system, the injector does not communicate with the powered device to negotiate its voltage or wattage requirements but merely supplies power at all times. Common 100 Mbit/s passive applications use the pinout of 802.3af mode B (see § Pinouts) – with DC positive on pins 4 and 5 and negative on 7 and 8, and data on 1 and 2, and 3 and 6, but polarization may vary. Gigabit passive injectors use a transformer on the data pins to allow power and data to share the cable and are typically compatible with 802.3af Mode A. Passive injectors with up to 12 ports are available.

Devices needing 5 volts cannot typically use PoE at 5 V on Ethernet cable beyond short distances (about 15 feet (4.6 m)) as the voltage drop of the cable becomes too significant, so a 24 V or 48 V to 5 V DC-DC converter is required at the remote end.^{[57][unreliable source?]}

Passive PoE power sources are commonly used with a variety of indoor and outdoor wireless radio equipment, most commonly from Motorola (now Cambium), Ubiquiti Networks, MikroTik and others. Earlier versions of passive PoE 24 VDC power sources shipped with 802.11a, 802.11g and 802.11n-based radios are commonly 100 Mbit/s only.

Passive DC-to-DC injectors also exist which convert a 9 V to 36 V DC, or 36 V to 72 V DC power source to a stabilized 24 V 1 A, 48 V 0.5 A, or up to 48 V 2.0 A PoE feed with '+' on pins 4 & 5 and '−' on pins 7 & 8. These DC-to-DC PoE injectors are used in various telecom applications.^[58]

The ISO/IEC TR 29125 and Cenelec EN 50174-99-1 draft standards outline the cable bundle temperature rise that can be expected from the use of 4PPoE. A distinction is made between two scenarios:

1. bundles heating up from the inside to the outside, and
2. bundles heating up from the outside to match the ambient temperature.

The second scenario largely depends on the environment and installation, whereas the first is solely influenced by the cable construction. In a standard unshielded cable, the PoE-related temperature rise increases by a factor of 5. In a shielded cable, this value drops to between 2.5 and 3, depending on the design.

802.3af/at/bt pin assignments from the Power Sourcing Equipment (PSE) perspective (MDI-X)

Pins at switch	T568A color	T568B color	10/100 mode B, DC on spares		10/100 mode A, mixed DC & data		1000 (1 Gbit/s) mode B, DC & bi-data		1000 (1 Gbit/s) mode A, DC & bi-data		1000 (1 Gbit/s) mode A+B (4PPoE), DC & bi-data[note 1]
Pin 1	White/green stripe	White/orange stripe	Rx +		Rx +	DC +	TxRx A +		TxRx A +	DC +	TxRx A +	DC +
Pin 2	Green solid	Orange solid	Rx −		Rx −	DC +	TxRx A −		TxRx A −	DC +	TxRx A −	DC +
Pin 3	White/orange stripe	White/green stripe	Tx +		Tx +	DC −	TxRx B +		TxRx B +	DC −	TxRx B +	DC −
Pin 4	Blue solid			DC +	Unused		TxRx C +	DC +	TxRx C +		TxRx C +	DC +
Pin 5	White/blue stripe			DC +			TxRx C −	DC +	TxRx C −		TxRx C −	DC +
Pin 6	Orange solid	Green solid	Tx −		Tx −	DC −	TxRx B −		TxRx B −	DC −	TxRx B −	DC −
Pin 7	White/brown stripe			DC −	Unused		TxRx D +	DC −	TxRx D +		TxRx D +	DC −
Pin 8	Brown solid			DC −			TxRx D −	DC −	TxRx D −		TxRx D −	DC −
Notes: ^ Only supported by 802.3bt for devices that identify as the newly added Type 3 or Type 4.[59]

• IEEE GET Program for free download of standards after registration
• ieee802.org: IEEE 802.3af Task Force
• ieee802.org: IEEE 802.3at Task Force
• ieee802.org: IEEE 802.3bt Task Force